扭剪扳手主要应用于钢结构安装行业，专门安装钢结构高强螺栓。高强螺栓可分为扭剪型和大六角型两种，国标扭剪型高强螺栓为M16、M20、M22、M24，非国标的扭剪型螺栓有M27、M30两种。

Twist shear wrenches are mainly used in the steel structure installation industry, specifically for installing high-strength bolts in steel structures. High strength bolts can be divided into two types: torsion shear type and large hexagonal type. The national standard torsion shear type high strength bolts are M16, M20, M22, and M24, while non national standard torsion shear type bolts are M27 and M30.

一般的，对于扭剪型高强螺栓的紧固都要经过初紧和终紧两个步骤，而且每步都需要有严格的扭矩要求。在实践中，操作人员紧固扭剪型高强度螺栓时，一般是先采用冲击扳手或定扭矩扳手完成初紧，然后再利用扭剪扳手完成终紧。在实际操作环境下，钢架连接结构上需要使用多个螺栓，形成了螺栓集群，若将螺栓一个一个地按顺序一次性完成紧固，会产生无法均等紧固的问题，正确的操作方式为先将螺栓集群的每一个螺栓进行一次紧固，即初紧，当一次紧固完成时，所有的螺栓达到了基本相同的一次紧固扭矩，然后再将螺栓进行终紧固，直到扭剪型螺栓的颈部被剪断为止。

Generally, the tightening of torsion shear high-strength bolts requires two steps: initial tightening and final tightening, and each step requires strict torque requirements. In practice, when tightening high-strength torsion shear bolts, operators usually use an impact wrench or a fixed torque wrench to complete the initial tightening, and then use the torsion shear wrench to complete the final tightening. In practical operating environments, multiple bolts are required on the steel frame connection structure to form a bolt cluster. If the bolts are tightened one by one in sequence, it will cause the problem of uneven tightening. The correct operating method is to first tighten each bolt in the bolt cluster, that is, initial tightening. When one tightening is completed, all bolts reach the basic same initial tightening torque, and then finally tighten the bolts until the neck of the shear type bolt is cut off.

现有的扭剪型77779193永利首页网址可分为初紧扭剪型77779193永利首页网址和终紧扭剪型77779193永利首页网址，它们通常都只有一种传动比输出。现有的初紧扭剪扳手的扭矩控制范围小，无法同时覆盖初紧和终紧高强度螺栓的扭矩需求，而现有的终紧扭剪型77779193永利首页网址，对扭矩不加控制，以扭剪断扭剪型高强度螺栓颈部为准，无法用于初紧高强度扭剪型螺栓。由此，对扭剪型高强度螺栓施工，需要一把初紧扭剪型扳手，通常可用冲击扳手或定扭矩扳手替代，还需要一把终紧扭剪型扳手，这样增加了用工成本，还增加了施工人员的搬运负担，特别是在高处作业时，携带两把电动工具非常不便。

The existing torque type electric wrenches can be divided into initial tightening torque type electric wrenches and final tightening torque type electric wrenches, which usually only have one transmission ratio output. The torque control range of the existing initial tightening torque wrench is small and cannot cover the torque requirements of both initial and final tightening high-strength bolts. However, the existing final tightening torque wrench does not control the torque and is based on the neck of the high-strength bolt, which cannot be used for initial tightening high-strength torque shear bolts. Therefore, for the construction of high-strength torsion shear bolts, an initial tightening torsion shear wrench is required, which can usually be replaced by an impact wrench or a fixed torque wrench. In addition, a final tightening torsion shear wrench is required, which increases labor costs and also increases the transportation burden of construction personnel. Especially when working at heights, carrying two electric tools is very inconvenient.

本文来自：扭剪型77779193永利首页网址更多的内容请点击：我们将会为您提问的问题提供一个满意的服务，欢迎您的来

This article is from: Torsion type electric wrench. For more information, please click: We will provide you with a satisfactory service for the questions you ask. Welcome to come